FLUKE 80T-IR PDF

Temperature is measured by pointing the probe at the surface to be measured, and reading the temperature on the test instrument display. It will damage the probe case. If the probe is exposed to significant changes in ambient temperature hot to cold or cold to hot , allow 20 minutes for temperature stabilization, before taking measurements. Do not operate the probe near large electrical or magnetic fields such as arc welders and induction heaters.

Author:Tocage Salrajas
Country:Kazakhstan
Language:English (Spanish)
Genre:Software
Published (Last):9 May 2013
Pages:155
PDF File Size:9.83 Mb
ePub File Size:14.41 Mb
ISBN:301-2-29477-334-4
Downloads:81274
Price:Free* [*Free Regsitration Required]
Uploader:Shakakora



Temperature is measured by pointing the probe at the surface to be measured, and reading the temperature on the test instrument display. It will damage the probe case. If the probe is exposed to significant changes in ambient temperature hot to cold or cold to hot , allow 20 minutes for temperature stabilization, before taking measurements.

Do not operate the probe near large electrical or magnetic fields such as arc welders and induction heaters. These fields can cause measurement errors. Condensation may form on the lens when going from a cold to hot environment - wait 10 minutes for condensation to dissipate before taking measurements. Connectors must only be plugged into voltage measurement input jacks of the test instruments.

Do not touch or hold by the front cone. Temperature readings can be affected by heat from the hand. Equipment use not specified by manufacturer may impair safety. Compatibility The probe is compatible with all DC millivolt measuring instruments that have a minimum of 1 M input impedance and accept safety shrouded, standard diameter 0.

Operation To take a measurement, perform the following steps: 1. Plug the red connector into the V dc input jack and the black connector into the common or ground input jack on the test instrument. Select mV dc on the test instrument. Slide the probe switch forward to the "ON" position. Point the tip of the probe as close as possible to the object being measured without touching the object.

Read the test instrument display. Sleep mode extends battery life. Flowever, for maximum battery life, switch the probe to the "OFF" position. Display Codes Under the conditions shown in Table 1, the meter will alternate between displaying a reading and Display Code. Emissivity All objects emit invisible infrared energy. This ability, called emissivity, is based upon the material that the object is made of and its surface finish.

Emissivity values typically range from 0. The probe senses this energy assuming that the target has an emissivity value of 0. This value is factory set in the probe. If the actual target emissivity is less than 0. To correct for this, apply masking tape or a coat of matte paint to the target. The resulting target will have an emissivity of approximately 0. Table 1. Replace the battery. OT Sleep mode or battery is dead. The closer you are to the object or target , the smaller the area or spot the probe is sensing.

For example when the probe is held at a mm 8 in. Flot spots can be missed if too large an area is included in the field of view, so get as close as possible! See Figure 2. If the surface to be measured is covered by frost or other material, clean it to expose the surface. If the surface to be measured is highly reflective such as polished metal, apply masking tape or a matte finish paint to the surface. If the probe seems to be giving incorrect readings check the front of the probe. There may be condensation or debris obstructing the sensor; clean per instructions in the maintenance section.

Quick Check For a quick check of the probe, point it directly at ice immersed in water slush , within specifications limits, specifications. Response Time: 1 second Spectral Response: 8 to 14 microns nominal Emissivity: pre-set 0.

Front-Window Cleaning as necessary 1. Blow off loose particles using clean compressed air. Gently brush remaining debris away with a camel hair brush or Q-tip.

Carefully wipe the surface with a moist Q-tip. The swab may be moistened with water or a water- based glass cleaner. Allow to air dry. Do not use solvents to clean the window. Case Cleaning To clean the exterior housing, simply use soap and water or a mild commercial cleaner. Wipe with a damp sponge or soft rag.

The warranty period is one year and begins on the date of shipment. Parts, product repairs, and services are warranted for 90 days. Fluke warrants that software will operate substantially in accordance with its functional specifications for 90 days and that it has been properly recorded on non-defective media.

Fluke does not warrant that software will be error free or operate without interruption. Fluke authorized resellers shall extend this warranty on new and unused products to end-user customers only but have no authority to extend a greater or different warranty on behalf of Fluke. Warranty support is available only if product is purchased through a Fluke authorized sales outlet or Buyer has paid the applicable international price. To obtain warranty service, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that service center, with a description of the difficulty, postage and insurance prepaid FOB Destination.

Fluke assumes no risk for damage in transit. Following warranty repair, the product will be returned to Buyer, transportation prepaid FOB Destination.

Following repair, the product will be returned to the Buyer transportation prepaid and the Buyer will be billed for the repair and return transportation charges FOB Shipping Point. Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation of incidental or consequential damages, the limitations and exclusions of this warranty may not apply to every buyer.

If any provision of this Warranty is held invalid or unenforceable by a court or other decision-maker of competent jurisdiction, such holding will not affect the validity or enforceability of any other provision Fluke Corporation Fluke Europe B. Box P. Outside the U. To locate an authorized service center, visit us on the World Wide Web: www. All rights reserved.

Printed in U. All product names are trademarks of their respective companies.

LEY 28687 PDF

FLUKE 80T-IR PDF

Save to an existing parts list Save to a new parts list. With the UUT powered on, check that the battery voltage is at least 7. Set the DMM to the 3. Add to a parts list. Refer to Figure 1 for equipment configuration.

CAR CRASH WHILE HITCHHIKING DENIS JOHNSON PDF

Fluke 80T-IR Manual De Usuario

Thank you for your feedback. Refer to Figure 1 for 80t-jr configuration. Power up the UUT and allow it to stabilize for five minutes. With the UUT powered on, check that the battery voltage is at least 7. Add to a parts list.

Related Articles